Ceiling Fan Repair Fall River MA Done Right
Wobble, hum, dead speed, or no spin at all
When a ceiling fan quits, you feel it fast, especially in a Fall River summer. Our ceiling fan repair Fall River MA service covers wobble, motor hum, dead pull chains, remote pairing failures, and lights that flicker on the same circuit. We work on all major brands, from Harbor Breeze to Hunter and Casablanca. Call (508) 446-9335 and we will get your air moving again.
Ceiling Fan Repair Fall River MA Explained
Ceiling fan repair Fall River MA is a diagnostic and repair service that restores a fan's motor, capacitor, wiring, and controls so it spins quietly at every speed again. We test the wall switch, pull chain, remote receiver, and blade balance before we touch a screw. Most fans fail at the capacitor, the pull-chain switch, or a loose wire nut inside the canopy. We diagnose all three in one visit and fix what is actually broken.
Fall River homes take a beating from salt air and humid summers. Fans in The Flint and along Sandy Beach corrode faster at the blade irons and downrod threads. Old two-wire ceiling boxes from knob and tube days often cannot carry a modern fan, and we see that constantly in Corky Row and Globe Village. If your fan hums but will not spin, or the light works while the blades sit still, that is a ceiling fan fix Fall River job we handle same-day.
Why Repair Beats Replacing
A quality fan motor lasts 15 to 20 years. Repairing it costs a fraction of a new unit and keeps the finish and blade set you already matched to the room.
Save the Fan You Own
A new 52-inch fan runs $120 to $400 plus install. Replacing a capacitor or pull-chain switch usually lands between $95 and $185, and the fan you already like stays on the ceiling. We quote the repair before we start.
Quiet Nights Return
Hum and rattle come from worn capacitors, loose blade screws, or a bent blade iron. We balance blades, torque every screw to spec, and test all three speeds. Most customers tell us the fan is quieter than the day it was hung.
Fix the Circuit, Not Just the Fan
A fan that trips the breaker points to a wiring fault, not the fan. We trace the circuit with a multimeter and non-contact voltage pen, check the Romex in the switch box, and confirm the breaker is a matched Square D or Eaton type before we close up.
Remote and Smart Control Restored
Ceiling fan remote repair Fall River calls are common after a power surge. We re-pair receivers, replace dip-switch modules, and check the wall control wiring so your remote, dimmer, and smart hub all talk to the fan again.
What Our Repair Visit Looks Like
Five steps, one visit in most cases. You get a clear diagnosis, an upfront price, and a fan that works before we pack up.
Phone Triage
You describe the symptom: no spin, hum, wobble, or dead light. We ask the fan brand, ceiling height, and whether the wall switch controls it. That five-minute call tells us which parts to load on the truck, so most jobs finish in one trip.
On-Site Diagnosis
We kill power at the panel, then test the switch leg, pull chain, and capacitor with a multimeter and non-contact voltage pen. Blade pitch, downrod tightness, and canopy wiring all get checked. Diagnosis takes 20 to 30 minutes and we tell you the price before any repair starts.
Repair or Replace Parts
Capacitors, pull-chain switches, remote receivers, and blade irons get swapped on the spot. If the motor windings are burned, we tell you straight and quote a replacement instead of charging for a repair that will not hold. Most part swaps take 30 to 45 minutes.
Balance and Speed Test
We rehang the blades, torque the screws, and run the fan through low, medium, and high. A wobble kit goes on if the blades are out of plane. You watch the test, so there is no question the fan is right when we leave.
Cleanup and Walkthrough
Drop cloth down, wire nuts tucked, canopy seated, and the breaker back on. We walk you through what failed and how to keep it running, then hand you the invoice. Total visit time runs 60 to 90 minutes for a standard repair.
Electrical Know-How Behind Every Repair
Our electricians hold Massachusetts Electrical License credentials through the Massachusetts Board of State Examiners of Electricians, and every job follows NEC and NFPA 70E safety practice. We work on ceiling fans daily, from simple pull-chain units to remote-controlled and smart-hub models. That means we know the difference between a bad capacitor and a bad wall switch before we open the canopy, and we carry the parts to prove it.
- Licensed electricians trained on motor capacitors, pull-chain switches, and remote receiver modules.
- Every repair follows NEC box-fill and grounding rules, checked with a GFCI tester and voltage tester.
- We stock Square D, Eaton, and Leviton parts so most repairs finish in a single visit.
- NFPA 70E arc-flash safety practice on every panel and switch-leg job, no exceptions.
- Diagnostic experience across Hunter, Casablanca, Harbor Breeze, and modern smart fans.
Why Fall River Calls Us for Ceiling Fan Repair Fall River MA
We are a local electrical shop, not a handyman service. Fans, wiring, and panels are what we do all day, and we price the repair before we start.
Upfront Repair Pricing
You hear the price before we open the canopy. A capacitor swap runs $95 to $185, a remote receiver $120 to $220, and a full motor replacement is quoted separately. No surprise line items, no hourly creep while you watch the clock.
Same-Day Slots Held Open
We keep same-day ceiling fan repair Fall River MA slots open for fans that quit in a heat wave. Call before noon and we usually reach you the same afternoon. Evening and weekend calls are available when the schedule allows.
We Fix the Cause, Not the Symptom
A fan that wobbles after a blade swap usually has a bent iron or a loose ceiling box. We check the box, the bracket, and the wiring with a torque wrench and voltage tester so the fix holds. That is the difference between a ceiling fan fix Fall River and a temporary patch.
Neighborhood-Level Familiarity
We work in Maplewood, Steep Brook, and the North End weekly. We know which streets have older two-wire boxes and which homes need a box brace before a heavier fan goes back up. That local knowledge saves you a second visit.
What Our Ceiling Fan Repair Covers
Every repair visit includes a full diagnostic, the part swap, a balance check, and a speed test. If the motor is beyond saving, we tell you and quote a replacement instead of charging for a repair that will not hold. Here is what is covered.
What's Included
Full Electrical Diagnosis
We test the switch leg, pull chain, capacitor, and remote receiver with a multimeter and non-contact voltage pen. You get a clear answer on what failed and what it costs to fix, before any work begins.
Capacitor and Switch Swap
Failed capacitors and burned pull-chain switches are the two most common fan faults. We carry matched replacements and install them on the spot, which restores every speed and stops the hum.
Remote and Receiver Repair
We re-pair remotes, replace receiver modules, and check dip-switch settings. If the wall control is the problem, we repair or replace it and confirm the fan responds to every input.
Blade Balance and Torque
Wobble comes from bent irons, loose screws, or out-of-plane blades. We balance the blade set, torque every fastener, and add a balance kit when needed so the fan runs smooth at high speed.
Ceiling Box and Bracket Check
A fan-rated box and brace are code requirements, not extras. We inspect the box, confirm the bracket is secure, and correct loose mounting so the fan does not work itself free over time.
Post-Repair Speed Test
Before we leave, we run the fan through low, medium, and high and check for hum, wobble, and flicker. You watch the test, so there is no doubt the repair is done right.
Fan Problems We Fix in Fall River
Most fan failures fall into a handful of patterns. Here are the ones we see most in Fall River homes, and what happens if you let them ride.
Fan hums but will not spin
A failed capacitor keeps the motor from starting, and running it that way overheats the windings until the fan is scrap.
We test the capacitor with a multimeter, swap in a matched replacement, and confirm all three speeds. Most of these repairs finish in under an hour and cost $95 to $185, which beats a new fan plus installation.
Blades wobble and shake the ceiling
Wobble loosens the box, cracks the canopy, and can pull a poorly braced fan free over months of use.
We check blade pitch, torque the irons, and inspect the ceiling box. If the box is not fan-rated, we install a listed brace and rehang the fan balanced, so the shake stops at the source.
Remote or wall control stopped working
A dead receiver or a surge-damaged module leaves you pulling a chain that may also be broken, so the fan is stuck on one speed or off entirely.
We re-pair the remote, replace the receiver, and test the wall control wiring. Ceiling fan remote repair Fall River calls are common after storms, and we carry the modules to fix most of them same-day.
Fan trips the breaker when it starts
A shared or overloaded circuit will keep tripping, and repeated trips wear the breaker until it fails open.
We trace the circuit, check the breaker type, and confirm the fan is not sharing a leg with a heavy load. If the panel is at its limit, we quote a breaker replacement or a 200-amp upgrade so the circuit is right.
When to Call for Ceiling Fan Repair
A bedroom fan quits during a July heat wave and the window AC cannot keep up.
We hold same-day ceiling fan repair Fall River MA slots for exactly this. Call before noon, describe the symptom, and we arrive with capacitors, switches, and receivers on the truck so most repairs finish in one visit.
Air moving again the same day, usually within 90 minutes of our arrival, at the price quoted on the phone.
A fan in a Corky Row rental wobbles so badly that tenants stop using it.
We inspect the blade irons, balance the set, and check the ceiling box for a proper fan-rated brace. If the box is undersized, we install a listed brace and rehang the fan before we leave.
A quiet fan the tenants actually use, and no more maintenance calls about the shake.
A power surge takes out the remote and receiver on a living room fan in the Highlands.
We test the receiver, replace the module, re-pair the remote, and check the wall control. We also quote whole-house surge protection so the next storm does not repeat the repair.
Remote, wall control, and app all working again, with the circuit protected against the next surge.
A homeowner in Steep Brook is selling and the inspector flags a wobbly fan with no box brace.
We correct the box, install a fan-rated brace, balance the blades, and confirm the grounding path meets NEC rules. We leave the install ready for reinspection.
A clean inspection item, a fan that runs smooth, and no delay at closing.
Tools and Methods We Use
Tools & Equipment
Fluke Multimeter
Tests capacitor values, switch continuity, and voltage at the fan canopy so we diagnose the real fault instead of guessing at parts.
Non-Contact Voltage Pen
Confirms the circuit is dead before we touch a wire, and verifies the switch leg is live when the fan should be getting power.
Klein Tools Insulated Screwdrivers
Rated for 1,000 volts, used on every canopy and switch-plate screw so a live circuit cannot reach the hand.
Torque Wrench
Sets blade iron and downrod screws to the manufacturer's spec, which is the difference between a fan that stays balanced and one that wobbles in a month.
GFCI Tester
Checks the circuit feeding the fan for proper grounding and GFCI protection, especially on porch and patio fan circuits.
Wire Strippers and Lineman's Pliers
Clean, correct strip lengths and tight splices with fresh wire nuts, so the connection inside the canopy stays solid for years.
Circuit Breaker Finder
Labels the exact breaker for the fan circuit, so future service and panel work is fast and safe for everyone.
Methods
NEC box-fill and grounding compliance
Every repair follows National Electrical Code rules for box fill, conductor sizing, and grounding. We confirm the fan-rated box and brace, then verify the ground path with a tester before we close the canopy.
NFPA 70E safe work practice
We de-energize at the panel, verify with a non-contact pen, and use insulated tools on every job. Arc-flash boundaries and PPE are standard on our trucks, not an afterthought.
Capacitor-first diagnosis
Most no-spin and one-speed fans fail at the capacitor. We test it first with a multimeter, which keeps the repair fast and the cost low instead of replacing parts on a hunch.
Blade balance and torque sequence
We rehang blades in a cross pattern, torque to spec, and run a balance check at high speed. That sequence eliminates the wobble that comes from uneven tightening.
How Ceiling Fan Repair Runs in Fall River
Fall River sits on the water, and that matters for ceiling fans. Salt air corrodes blade irons and downrod threads faster than inland towns, and humid summers push motors harder. We see corroded irons in Sandy Beach and Steep Brook constantly, and we carry replacements on the truck. Older housing stock is the other factor. Knob and tube wiring in Corky Row and Globe Village often feeds a fan box with no ground and no brace, so a repair there means correcting the box before the fan goes back up. We check the Romex, confirm the breaker type, and bring the circuit up to NEC standards as part of the job. If you need an affordable ceiling fan fix Fall River MA homeowners trust, we quote the whole scope before we start, including any box correction. Winter calls run lighter, but spring and summer are our busiest stretch, so same-day slots fill fast once the heat arrives.
Service Areas
Coastal humidity corrodes blade irons and downrod threads here, so we often replace hardware along with the failed part.
Older two-wire fan boxes are common, and many need a listed brace and a grounding correction before the fan is rehung.
Post-war homes with shared fan and lighting circuits, where a dedicated leg often fixes the flicker on fan startup.
Salt air exposure means we check every blade iron and screw for corrosion, not just the electrical fault.
Larger homes with multiple fans, where we often find one overloaded circuit feeding two or three units.
Local Considerations
Salt air along the waterfront
Corrodes blade irons and downrod threads, so repairs here include hardware inspection and replacement, not just the electrical part.
Knob and tube wiring in older homes
Leaves fan boxes ungrounded and unbraced, so we correct the box and ground path as part of the repair to meet NEC rules.
Humid summers with heavy fan runtime
Motors and capacitors run hot for months, which shortens capacitor life and makes same-day summer slots our busiest service.
Winter storm outages
Power surges during outages damage remote receivers and smart modules, so we carry replacements and quote surge protection on those calls.
Bedroom Fan Dead in July Heat
A homeowner in The Flint had a 52-inch fan that hummed and then stopped spinning entirely during a heat wave. The wall switch was live, the pull chain clicked, but the blades never moved. The room was unusable at night.
We tested the capacitor, found it failed open, and installed a matched replacement in about 40 minutes. All three speeds came back, the hum was gone, and the total bill was $145, well under the cost of a new fan plus installation.
Maintenance & Follow-up
Run the fan on medium rather than high for long stretches, and wipe the blade irons twice a year to slow salt-air corrosion. If the hum returns, call before the motor overheats.
A power surge in the Highlands killed the remote receiver on a living room fan. The fan was stuck on high with no way to change speed, and the wall control did nothing. The homeowner was ready to buy a new unit.
We replaced the receiver module, re-paired the remote, and tested the wall control. The fan responded to every input again, including the app. The repair came in at $180, and we quoted whole-house surge protection to prevent a repeat.
Maintenance & Follow-up
Keep the remote receiver away from direct heat, and have surge protection installed at the panel. Re-pair the remote after any extended outage if the fan acts up.
A landlord in Corky Row had a tenant complaint about a fan that shook the ceiling. The inspection also flagged the box as unbraced. The fan was a code item and a noise problem at the same time.
We installed a listed fan-rated brace, corrected the grounding, balanced the blade set, and torqued every screw to spec. The wobble stopped, the inspection item cleared, and the total was $260 for parts and labor.
Maintenance & Follow-up
Check blade screws each season and keep the fan on a balanced setting. If a blade gets bent, replace the iron rather than bending it back.
What Ceiling Fan Repair Costs
Typical 2026 pricing in the Fall River area runs $95 to $260 for most repairs. A capacitor or pull-chain switch sits at the low end, a remote receiver or motor replacement sits higher, and a box correction adds parts and time. We quote the exact price after a 20-minute diagnosis, before any work starts. If the motor is beyond saving, we tell you and quote a replacement instead of charging for a repair that will not hold. That is how a ceiling fan fix Fall River homeowners recommend should work.
Pricing Factors
Failed part type
A capacitor runs $95 to $185 installed. A pull-chain switch sits in the same range. A remote receiver or motor replacement pushes the total to $180 to $260 or more, depending on the fan model and part availability.
Fan height and access
A standard 8-foot ceiling is quick work. Cathedral ceilings, tight closets, or a fan over a stairwell add ladder time and can add $40 to $90 to the labor portion of the job.
Box and brace condition
If the ceiling box is not fan-rated or the brace is missing, we install a listed brace and correct the mounting. That adds $60 to $140 in parts and labor but is required for a safe, code-compliant repair.
Wiring condition
Loose splices, damaged Romex, or ungrounded knob and tube wiring need correction before the fan goes back up. Simple splice repairs are quick; a circuit correction adds time and cost.
Brand and part availability
Common brands like Hunter and Harbor Breeze use stock parts we carry. Specialty or discontinued fans may need a special-order receiver or motor, which adds two to three business days and a small parts premium.
After-hours or weekend call
Evening and weekend visits carry a modest scheduling premium. Same-day weekday slots booked before noon stay at the standard rate whenever the schedule allows.
Investment Range
$95 - $260 for most repairs; $300 - $650 if a motor replacement or box correction is needed
Based on project scope
Value You Get
Repairing a fan you already own costs a fraction of a new unit plus installation, and it keeps the finish and blade set matched to your room. We quote before we start, so the number you hear is the number you pay.
How much does ceiling fan repair cost in Fall River?
Most ceiling fan repairs in Fall River run $95 to $260 in 2026, depending on the part. A capacitor or pull-chain switch sits at the low end; a remote receiver or motor replacement sits higher. We quote the exact price after a 20-minute diagnosis, before any work starts. Call (508) 446-9335 for a same-day slot.
Why is my ceiling fan not working in Fall River MA?
The three most common causes are a failed capacitor, a burned pull-chain switch, and a loose wire nut inside the canopy. Salt air and humid summers in Fall River also corrode blade irons and downrod threads, which shows up as wobble. We test all three with a multimeter and tell you which one failed.
Can a ceiling fan be repaired in Fall River Massachusetts?
Yes. Nearly every fan we see can be repaired rather than replaced. Capacitors, switches, receivers, blade irons, and light kits are all serviceable parts. The exception is a motor with burned windings, which we will tell you honestly and quote a replacement for instead of charging for a repair that will not last.
How long does ceiling fan repair take in Fall River?
A standard repair takes 60 to 90 minutes on site, including diagnosis, the part swap, and a full speed test. If we need a special-order receiver or motor, the return visit is usually within two to three business days. Same-day ceiling fan repair Fall River MA slots are held for fans that quit during heat waves.
Licensed, Insured, and Local
Certifications
Reviews
Called about a fan that quit in the heat. They came the same afternoon, tested the capacitor, and had it spinning in under an hour. Price matched the phone quote exactly. Clean work and they showed me the speed test before leaving.
Our remote-controlled fan died after a storm and I thought we needed a new one. They replaced the receiver, re-paired the remote, and checked the wall control. Saved us a few hundred dollars and the fan works with the app again.
Rental property fan was wobbling and the inspection flagged the box. They braced it, balanced the blades, and cleared the code item in one visit. Straight answers on price and no upsell. I use them on all three units now.
Fan in the living room only ran on one speed. Turned out to be the wall control, not the fan. They repaired it, tested every position, and explained what to watch for. Fast, tidy, and honest about what the job needed.
Other Electrical Work We Handle
Electrical Panel Upgrades
A fan that trips the breaker every time it starts often points to a panel at its limit. We upgrade to a 200-amp service with Square D or Eaton breakers, which gives your fans and AC room to run without nuisance trips.
Electrical Panel UpgradesCircuit Breaker Replacement
Fans draw surge current at startup, and a weak breaker will trip on that spike. We replace worn breakers with matched Eaton or Siemens units and torque the lugs to spec, so your ceiling fan repair Fall River MA job actually holds.
Circuit Breaker ReplacementFuse Box Replacement
Older Fall River homes still run screw-in fuse boxes that cannot handle a modern fan plus AC load. We swap them for a breaker panel with AFCI protection, which stops the nuisance blows that send people hunting for fuses mid-summer.
Fuse Box ReplacementElectrical Outlet Repair
Dead outlets in the same room as a dead fan usually share a circuit fault. We test with a GFCI tester and non-contact voltage pen, then repair the loose backstab or burned receptacle so the whole room works again.
Electrical Outlet RepairGFCI Outlet Installation
Kitchen, bath, and garage circuits need GFCI protection under current code. We install Leviton GFCI outlets and confirm trip times, which protects the circuit your fan and lighting share in older Fall River layouts.
GFCI Outlet InstallationLight Switch Repair
A fan that only runs on one speed often has a bad wall control, not a bad fan. We repair or replace the switch, check the switch leg, and confirm the fan responds to every position before we close the plate.
Light Switch RepairElectrical Wiring Repairs
Loose wire nuts and nicked conductors inside a fan canopy cause intermittent power. We repair the splice, replace damaged Romex, and re-terminate with fresh wire nuts so the fan gets steady voltage at every speed.
Electrical Wiring RepairsWhole-Home Rewiring
Homes with knob and tube wiring cannot safely carry modern fan and AC loads. We rewire room by room with Romex and THHN, adding grounded circuits so your ceiling fan repair Fall River Massachusetts work has a solid foundation.
Whole-Home RewiringAluminum Wiring Repair
Aluminum branch wiring in some Fall River homes overheats at fan and light connections. We install approved copper pigtails and anti-oxidant compound, which removes the fire risk and stabilizes the voltage your fan motor sees.
Aluminum Wiring RepairKnob and Tube Wiring Replacement
Knob and tube has no ground and cannot carry a fan safely. We replace it with grounded Romex, add proper boxes, and bring the circuit up to NEC standards before any new fan goes up.
Knob and Tube Wiring ReplacementElectrical Code Corrections
Unpermitted fan installs often miss box bracing and grounding. We correct box fill, add a listed fan-rated brace, and fix the grounding path so the install passes inspection and the fan stops wobbling.
Electrical Code CorrectionsSurge Protection Installation
Power surges fry fan receivers and smart modules. We install whole-house surge protection at the panel, which absorbs the spike before it reaches your fan controls and saves you a repeat remote repair.
Surge Protection InstallationWhole-House Surge Protectors
A single storm can take out a fan receiver, a thermostat, and a TV. A whole-house surge protector wired to your panel clamps the surge at the source, protecting every ceiling fan and smart device in the house.
Whole-House Surge ProtectorsGenerator Installation
Fall River outages during winter storms leave fans and heat off. A standby generator keeps the critical circuits live, and we size the transfer switch so your fan and furnace both run during an outage.
Generator InstallationStandby Generator Repair
A generator that will not transfer leaves the house dark. We diagnose the transfer switch, test the control wiring with a multimeter, and repair the fault so your backup power actually backs you up.
Standby Generator RepairPortable Generator Hookup
We install a proper inlet box and interlock so a portable generator feeds selected circuits safely. No backfeeding, no extension cords through a window, and your fan circuit stays protected during the outage.
Portable Generator HookupTransfer Switch Installation
A manual or automatic transfer switch keeps generator power off the grid lines. We install and label the switch, then test it under load so you know exactly which circuits, including fans, come back on.
Transfer Switch InstallationCeiling Fan Installation
If the motor is truly gone, we install a new fan with a listed brace, balanced blades, and a matched wall control. We hang it, wire it, and run it through all speeds so it is quiet from day one.
Ceiling Fan InstallationLight Fixture Installation
Fan light kits and separate fixtures share the same switch leg. We install and balance the fixture, confirm the box rating, and make sure the fan and light do not fight for the same circuit.
Light Fixture InstallationRecessed Lighting Installation
Can lights and ceiling fans in the same room need balanced circuit load. We install IC-rated recessed fixtures, check the circuit math, and confirm the fan still gets full voltage at high speed.
Recessed Lighting InstallationOutdoor Lighting Installation
Porch and patio fans need damp-rated wiring and GFCI protection. We install the circuit with weather-rated boxes and a GFCI tester check, so your outdoor fan and lights run safely through coastal humidity.
Outdoor Lighting InstallationSecurity Lighting Installation
Motion lights and fans often share a circuit in Fall River homes. We wire the lighting on its own leg where possible, which stops the flicker you see when the fan starts and the lights dim.
Security Lighting InstallationLandscape Lighting Installation
Low-voltage landscape lighting and a garage fan can overload one circuit. We split the load, install a proper transformer, and confirm the fan still runs at full speed with the lights on.
Landscape Lighting InstallationMotion Sensor Light Installation
A motion sensor that shares a switch leg with a fan can cause flicker. We install the sensor on a dedicated leg, set the sensitivity, and test it so the fan and light do not interfere.
Motion Sensor Light InstallationDimmer Switch Installation
Not every dimmer plays well with a fan motor. We install a fan-rated control, confirm compatibility with your fan, and eliminate the buzz that comes from the wrong dimmer on a motor load.
Dimmer Switch InstallationSmart Home Electrical Installation
Smart fans need a neutral at the switch and a stable circuit. We run the neutral, install the hub-compatible switch, and pair the fan so your app, remote, and voice control all work together.
Smart Home Electrical InstallationSmart Thermostat Installation
A smart thermostat and ceiling fan work together to cut cooling costs. We install the thermostat with a C-wire, confirm the HVAC wiring, and set the fan schedule so both systems run efficiently.
Smart Thermostat InstallationEV Charger Electrical Repair
A Level 2 charger pulls serious current, and a shared circuit will trip. We repair the charger circuit, verify the breaker size, and confirm your fan circuit is not sharing the load.
EV Charger Electrical Repair200 Amp Electrical Panel Upgrade
Modern homes with AC, EV charging, and multiple fans need more capacity. We upgrade to a 200-amp panel with AFCI and GFCI breakers, which ends the nuisance trips and gives every fan a clean circuit.
200 Amp Electrical Panel UpgradeWhat Fall River Customers Say
Real experiences from customers who chose our Ceiling Fan Repair services
"Our bedroom fan started humming and then quit on the hottest week of July. They came out the same afternoon, tested the capacitor, and had a replacement in the truck. Forty minutes later it was spinning quiet on all three speeds. Price was exactly what they quoted on the phone."
Maria S.
Homeowner, The Flint
"The remote on our living room fan stopped working after a storm. I figured we needed a whole new fan. They re-paired the receiver, replaced a dip switch module, and checked the wall control. Saved us a few hundred dollars and the fan works with the remote and the app again."
Dave R.
Homeowner, Maplewood
"I manage three units and one fan was wobbling so bad tenants complained. They found a bent blade iron and a loose ceiling box, braced it, and balanced the blades. No wobble, no noise, and they showed me the torque on the screws before they left. I use them for all three units now."
Karen L.
Landlord, Corky Row
Get Your Ceiling Fan Repair Fall River MA Booked
One call gets a licensed electrician to your door with the parts to fix most fans on the first visit. We quote the repair before we start, and we test every speed before we leave. Call (508) 446-9335 now.