Portable Generator Hookup Fall River MA Done Right
Code-compliant inlet box and transfer switch installation
A portable generator hookup Fall River MA homeowners can trust keeps your heat, fridge, and sump pump running when the grid drops. We install the inlet box, run the wiring, and mount a manual transfer switch so you plug in outside and flip breakers inside, with no extension cords through a window. If you need a portable generator connection Fall River wide before winter storms hit, our licensed electricians handle it in one visit.
Portable Generator Hookup Fall River MA Explained
A portable generator hookup Fall River MA is an electrical installation that connects a portable generator to your home's wiring through an outdoor inlet box and a transfer switch, so selected circuits power up without backfeeding the utility lines. We mount the inlet box on an exterior wall, run THHN wire or Romex cable through conduit to a manual or automatic transfer switch near your panel, and label the circuits you want backed up. Most homes get 6 to 10 backed-up circuits, enough for a furnace, refrigerator, sump pump, and a few lights.
Fall River's older housing stock makes this work specific. Triple-deckers in The Flint and Corky Row often still have 60-amp fuse boxes or undersized panels that cannot safely carry a generator feed, and coastal homes near Sandy Beach deal with corroded outdoor boxes after salt-heavy winters. We check your panel with a circuit breaker finder and voltage tester first, then size the inlet and transfer switch to match. If you have been searching for a portable generator inlet box near me Fall River, this is the exact job we do every week.
Why Fall River Homeowners Add Generator Hookups
A proper hookup turns a noisy, cord-tangled outage into a two-minute routine. Here is what changes once the inlet box and transfer switch are in.
No More Extension Cords
Running cords through a cracked window to power a fridge is how people get CO poisoning. With a portable generator connection Fall River homeowners plug one cord into the outdoor inlet box, and power reaches your panel through permanent wiring. You keep doors and windows shut, and your generator stays outside where it belongs.
Protects Linemen And You
Backfeeding a dryer outlet sends 240 volts onto the utility lines and can kill a line worker. A transfer switch mechanically breaks the connection to the grid before generator power flows. That single device is the difference between a legal, insurable installation and a serious code violation.
Runs Your Critical Circuits
We label 6 to 10 circuits so you know exactly what stays live: furnace or boiler, refrigerator, sump pump, well pump, internet router, and kitchen outlets. A 7,500-watt portable generator typically carries that load comfortably. You flip the transfer switch, start the generator, and the house hums along.
Adds Real Resale Value
A permitted generator hookup with a transfer switch is a documented improvement. Buyers in Bristol County ask about storm readiness, and an inspection-ready installation answers that question. It also pairs naturally with a 200 Amp Electrical Panel Upgrade if your service is still running on 100 amps.
Our Portable Generator Hookup Process
Every job follows the same five steps, from the first phone call to the final test. Most installations finish in a single day.
Phone Assessment
We ask what you want to run during an outage, what generator you own or plan to buy, and where your panel sits. You get an upfront price range before we schedule. If you are comparing portable generator hookup cost Fall River MA quotes, this call takes about ten minutes and saves you a wasted service visit.
On-Site Load Check
Our electrician opens the panel, checks the main breaker rating, and looks for double-tapped breakers, aluminum wiring hazards, or a fuse box that needs replacement first. We use a multimeter and non-contact voltage pen to confirm the service is safe to tie into. This inspection takes 20 to 30 minutes.
Inlet And Switch Install
We mount a Leviton or Hubbell inlet box on the exterior wall nearest your panel, drill through the rim joist, and pull Romex cable or THHN wire in conduit to a Square D or Eaton transfer switch. A torque wrench sets every lug to spec. Rough-in usually runs two to three hours.
Circuit Labeling
We move the chosen circuits onto the transfer switch and label each one on the panel door. You get a printed card showing what runs on generator power and the wattage each circuit draws. This step takes about an hour and is where most DIY installs fall apart.
Test And Walkthrough
We start a load test, confirm the transfer switch isolates the utility feed, and check voltage at each backed-up outlet with a Fluke meter. Then we walk you through the plug-in sequence and generator sizing. Total time on site is typically four to six hours.
Generator Hookup Expertise You Can Verify
Our electricians hold Massachusetts Electrical License credentials and work under the Massachusetts Board of State Examiners of Electricians. We install transfer switches and inlet boxes to NEC and NFPA 70E standards, and we pull permits on every hookup so the work is inspected. Fall River's mix of two-family flats, triple-deckers, and post-war ranches means we have seen nearly every panel configuration in Bristol County. We also handle the follow-up work, from GFCI outlet installation to whole-home rewiring, so one crew can bring an older service up to code.
- Licensed Massachusetts electricians trained on manual and automatic transfer switch wiring
- Every hookup permitted and inspected under NEC Article 702 for optional standby systems
- Panel and service checks with Fluke meters and Klein Tools before any generator feed is tied in
- Experience with 60-amp fuse boxes, 100-amp panels, and 200-amp upgrades across Fall River
- NFPA 70E and OSHA safety practices on every job, including lockout during panel work
Why Choose Our Portable Generator Hookup Fall River MA Team
We are a local electrical shop, not a national franchise. That means the person who answers the phone can be at your panel the same week, and the electrician who wires your inlet box is the one who tests it.
Same-Day Service Available
Storm warnings in Bristol County usually give us 24 to 48 hours of notice, and we reserve slots for same-day portable generator connection Fall River MA calls. If your generator is already sitting in the garage and the forecast turns ugly, call us before the shelves empty at the hardware store.
Upfront Pricing, No Surprises
You get a written price range before we start, and it holds unless we find a hidden problem like a melted bus bar or knob and tube wiring. No hourly meter running while we figure things out. The number we quote is the number you pay for the scope we agreed on.
Permits And Inspection Handled
We pull the electrical permit and meet the inspector on site. That matters at resale and with insurance claims after a storm. An unpermitted hookup can void a homeowner policy, and we have seen it happen in Fall River more than once.
We Size The Generator To The House
A 5,000-watt generator will not start a well pump and a furnace together. We calculate starting watts for your actual appliances, then tell you the minimum generator size before you buy. That advice alone saves customers hundreds on the wrong unit.
What Our Generator Hookup Includes
Every hookup covers the parts and labor to connect your portable generator to your home safely. We handle the permit, the inspection, and the walkthrough. If your panel needs work first, we tell you before we start, not after.
What's Included
Weatherproof Inlet Box
A 30-amp or 50-amp outdoor inlet box mounted near where your generator will sit, wired with THHN wire or Romex cable in conduit. We seal the penetration so Fall River rain and snow stay outside.
Transfer Switch
A manual or automatic transfer switch installed at your panel, sized to your service and generator. It mechanically isolates the utility feed so generator power never backfeeds the grid.
Circuit Selection And Labeling
We move 6 to 10 circuits onto the switch and label each one. You get a printed card listing what runs on generator power and the wattage each circuit draws.
Permit And Inspection
We pull the electrical permit with the city and meet the inspector on site. The signed inspection card documents the work for your records and your insurance company.
Load Test And Walkthrough
We run a live load test, verify voltage at each backed-up outlet with a Fluke meter, and show you the exact plug-in and switchover sequence before we leave.
Problems A Generator Hookup Solves
Fall River outages tend to arrive with nor'easters and ice storms, and they last longer than most people expect. These are the problems we hear about most, and how a proper hookup fixes each one.
Cords running through windows and doors
Carbon monoxide seeps back into the house, door seals get crushed, and someone trips over the cord in the dark. It is the most common cause of generator-related ER visits during outages.
We install an outdoor inlet box so the generator cord stays outside. Power travels through permanent wiring to your panel, and every door and window stays shut. One connection point, no tripping hazards.
Backfeeding a dryer outlet
Energizing the utility lines can electrocute a line worker and destroy your generator when power returns. It also voids most homeowner insurance policies.
A transfer switch breaks the utility connection before generator power flows. We install and test the interlock, then show you how it works. The inspector confirms it meets NEC Article 702.
Undersized panel with no spare breakers
A 60-amp fuse box or full 100-amp panel has nowhere to land the transfer switch. Homeowners buy a generator, then discover it cannot be connected without more work.
We check the panel first and quote any upgrade in the same estimate. A 200 Amp Electrical Panel Upgrade gives you the capacity and breaker space, and we complete both jobs together.
Generator sized wrong for the load
A unit that cannot start the well pump or furnace leaves you hauling it back to the store mid-storm. Starting watts on a furnace or pump can be three times the running watts.
We calculate starting and running watts for your actual appliances before you buy. You get a minimum generator size in writing, and we label circuits to match so the load never exceeds capacity.
When Fall River Homeowners Use Generator Hookups
A nor'easter knocks out power for two days in the Highlands and the basement sump pump stops running.
We put the sump pump, furnace, refrigerator, and a few lights on the transfer switch. When the storm hits, you plug the generator into the inlet box, flip the switch, and the pump keeps the basement dry.
No flooded basement, no spoiled food, and heat stays on through the outage. The whole switchover takes about two minutes.
A landlord in Corky Row owns two triple-deckers and tenants call every time the grid flickers.
We install a hookup on each service, label the circuits, and walk the tenants through the plug-in sequence. Both units get permitted, inspected installations with printed instructions.
Tenants handle outages themselves, and the landlord stops fielding midnight calls. The documented install also supports the property's resale value.
A homeowner near Sandy Beach has a 100-amp panel with no spare spaces and wants backup before winter.
We upgrade to a 200-amp panel, install the inlet box on the ocean-facing wall with sealed conduit, and mount a manual transfer switch. Salt-resistant hardware protects the outdoor connection.
The house is storm-ready before the first freeze, with room on the panel for future circuits and an inspection card on file.
A family on the Tiverton line runs a home office and cannot afford a multi-day internet outage.
We put the router, modem, office outlets, and a hallway light on the transfer switch. A 5,000-watt generator carries that load easily, so we size the inlet box at 30 amps.
Work continues through the outage. The client stays on calls and meets deadlines while the neighborhood waits for the lines to come back.
Tools And Methods We Use
Tools & Equipment
Fluke Multimeter
Verifies voltage at every backed-up outlet and confirms the transfer switch isolates the utility feed before generator power flows. We log readings at each circuit during the final test.
Klein Tools Non-Contact Voltage Pen
Checks for live conductors before we open a panel or land a wire. It is the first tool out of the bag on every job and the reason nobody gets surprised.
Torque Wrench
Sets every lug on the transfer switch and inlet box to the manufacturer's inch-pound spec. Loose terminations are the leading cause of generator hookup failures and panel fires.
Conduit Bender And Fish Tape
Runs THHN wire through EMT or PVC conduit from the inlet box to the panel, and pulls cable through finished walls and rim joists without cutting unnecessary holes.
Circuit Breaker Finder
Maps which breaker controls each outlet before we move circuits onto the transfer switch. It prevents mislabeled panels and keeps the backed-up circuit list accurate.
GFCI Tester
Confirms GFCI protection on basement, garage, and kitchen circuits that will run on generator power. Required by code in those locations and tested on every hookup.
Methods
NEC Article 702 Optional Standby Systems
The code section that governs portable generator hookups. It requires a listed transfer switch, proper grounding and bonding, and inlet sizing matched to the generator. Every install we do is built to this standard and inspected against it.
Manual Transfer Switch Interlock
A mechanical interlock that makes it impossible to have utility and generator power connected at the same time. We install, test, and label the switch so the sequence is obvious to anyone in the house.
Load Calculation And Circuit Mapping
We add up starting and running watts for the appliances you want backed up, then map each one to a breaker. That math determines your minimum generator size and which circuits go on the switch.
NFPA 70E Safe Work Practices
Panel work happens with lockout and proper PPE. We de-energize where possible, test before touching, and follow the same safety standard used in commercial electrical work.
How Generator Hookups Run In Fall River
Fall River sits on the water, and that shapes the work. Salt air corrodes outdoor inlet boxes faster than inland, so we use sealed, corrosion-resistant hardware and mount boxes where snow and ice slide off the roof. The city's housing stock is old: triple-deckers in The Flint and Corky Row often still carry 60-amp fuse boxes, and post-war ranches in the Highlands and Maplewood frequently have 100-amp panels with every breaker space filled. Both need attention before a transfer switch can be landed. Winter storms drive most calls, but we install year-round so you are not competing for an appointment after the forecast turns. If you want a portable generator hookup in West End Fall River or anywhere else in the city, we pull the permit with the local inspectional services and meet the inspector on site. Most jobs finish in one day, and we leave you with labeled circuits and a printed switchover card.
Service Areas
Dense triple-decker housing with older 60-amp fuse boxes. Panel upgrades are common before a transfer switch can be installed.
Coastal exposure means salt corrosion on outdoor inlet boxes. We use sealed, marine-grade hardware and mount above snow line.
Post-war homes with 100-amp panels. Many have no spare breaker spaces, so a 200-amp upgrade often comes first.
Multi-family rentals where one hookup often serves several tenants. We label circuits clearly and provide printed instructions.
Mix of older two-families and renovated homes near the Tiverton line. Conduit runs through finished basements are routine here.
Local Considerations
Nor'easters and ice storms from November through March
Outages lasting 12 to 48 hours are common, which makes a generator hookup a practical necessity rather than a luxury. We prioritize installs before the first major storm.
Salt air along the waterfront
Outdoor inlet boxes corrode within a few seasons if they are not sealed and mounted correctly. We choose hardware rated for coastal exposure and seal every penetration.
Aging panels and fuse boxes in older neighborhoods
Roughly half the homes we visit need a panel upgrade or fuse box replacement before the hookup. We quote both together so there are no surprises.
Finished basements with limited access
Running conduit from an exterior wall to the panel can require soffit or ceiling routing. We plan the path first to minimize drywall repair.
60-Amp Fuse Box To Generator-Ready Panel
A 1920s triple-decker in The Flint had a 60-amp fuse box with cloth wiring and no equipment ground. The owner had bought a 7,500-watt generator but had no safe way to connect it and was running cords through a kitchen window.
We replaced the fuse box with a 200-amp panel, ran new grounded circuits, and installed a 50-amp inlet box with a 10-circuit manual transfer switch. The load test showed steady voltage on all ten circuits, and the inspection passed on the first visit.
Maintenance & Follow-up
Exercise the transfer switch twice a year and run the generator under load for 20 minutes each month. Check the inlet box gasket every fall before storm season.
A Sandy Beach homeowner had a hookup installed years earlier by someone else. The inlet box was corroded, the cover was cracked, and the conduit had pulled away from the wall. Salt air had eaten the terminals down to bare metal.
We replaced the inlet box with a sealed, corrosion-resistant unit, re-routed the conduit with proper strapping, and re-terminated the wiring. Voltage readings at the panel were steady, and the new box sat above the snow line where runoff could not reach it.
Maintenance & Follow-up
Inspect the inlet box each spring for corrosion and spray the terminals with a dielectric protectant. Replace the gasket every two years on coastal properties.
A remote worker on the Tiverton line lost two days of billable time during a 30-hour outage. The router, modem, and office outlets were all on a single circuit with no backup, and the family had been using a small inverter plugged into a car.
We installed a 30-amp inlet box and a 6-circuit transfer switch covering the office outlets, router, modem, hallway light, refrigerator, and furnace. A 5,000-watt generator now carries the load, and the client worked through the next outage without interruption.
Maintenance & Follow-up
Keep the generator fuel stabilized and start it monthly. Label any new office equipment so it stays on the backed-up circuit and does not overload the 5,000-watt unit.
Portable Generator Hookup Pricing
Typical 2026 pricing in Fall River runs $650 to $1,800 for a complete hookup with inlet box, transfer switch, wiring, and permit. A straightforward 6-circuit manual switch on a panel with open spaces lands near the low end. Longer conduit runs, a finished basement, or a panel upgrade push the number higher. We quote a range on the phone and confirm it after the on-site load check. If you want a portable generator hookup Fall River Massachusetts homeowners consider affordable, ask about pairing it with a 200 Amp Electrical Panel Upgrade to spread the cost across one project.
Pricing Factors
Transfer Switch Type
A manual 6-circuit switch is the least expensive option and works well for most homes. A 10-circuit or automatic switch costs more but backs up more appliances or handles switchover without you being home.
Panel Condition
If your panel has open breaker spaces and a modern main breaker, the hookup is straightforward. A full panel, a 60-amp fuse box, or a double-tapped bus adds a panel upgrade to the scope.
Conduit Run Length
The distance from the inlet box to the panel drives material and labor. A short run through an unfinished basement is quick. A long run through finished walls or a second floor takes more time and patching.
Inlet Box Amperage
A 30-amp inlet suits generators up to about 7,500 watts. A 50-amp inlet handles larger units and costs more in parts. We size it to your generator so you do not pay for capacity you will never use.
Permit And Inspection Fees
The city charges a permit fee based on the scope of work. We include it in the quote so the number you approve is the number you pay, inspection included.
Investment Range
$650 - $1,800 depending on panel condition, switch type, and run length
Based on project scope
Value You Get
A hookup costs less than a standby generator and protects the appliances you already own. One avoided basement flood or freezer full of spoiled food often covers a meaningful share of the bill.
How much does portable generator hookup cost in Fall River?
Most portable generator hookup cost Fall River MA projects run $650 to $1,800 in 2026, including the inlet box, transfer switch, wiring, and permit. A basic 6-circuit manual switch on a panel with room is at the low end. Add a subpanel, conduit run through a finished basement, or a 200-amp service upgrade and you move toward the top. We quote the range before we schedule.
Can I connect a portable generator to my house in Fall River MA?
Yes, and it is legal when the connection goes through a listed transfer switch or inlet box. What you cannot do is plug a generator into a dryer outlet or backfeed a breaker, which is a code violation and a shock hazard to utility crews. A licensed electrician installs the inlet and switch, pulls the permit, and the inspector signs off. The whole job usually takes one day.
What is a generator inlet box in Fall River Massachusetts?
A generator inlet box is a weatherproof outdoor receptacle, typically a Leviton or Hubbell model rated 30 or 50 amps, that your generator's cord plugs into. From there, permanent wiring carries power to the transfer switch at your panel. It keeps the generator outside, eliminates cords through doorways, and gives you a single connection point. We mount it within a few feet of where your generator will sit.
Is portable generator hookup safe in Fall River?
It is safe when a transfer switch breaks the utility connection before generator power flows. That interlock prevents backfeeding, the leading cause of electrocution for line workers during outages. We also test every backed-up circuit with a GFCI tester and Fluke meter, verify grounding and bonding, and confirm the generator sits at least 20 feet from doors and windows to avoid carbon monoxide. Safety is the whole point of doing this to code.
Licensed, Permitted, And Reviewed
Certifications
Reviews
Installed our inlet box and transfer switch in one afternoon. They labeled every circuit and showed us exactly how to switch over. We used it during the last storm and everything ran perfectly. Fair price and no mess left behind.
Called about a generator hookup and they walked me through generator sizing before I bought anything. Saved me from buying a unit that was too small. Install was clean and the inspector passed it the same week.
Our old fuse box had to go before they could install the transfer switch. They quoted both jobs together, did the panel upgrade and hookup in one day, and cleaned the basement better than they found it. Highly recommend.
Professional from the first phone call. They pulled the permit, met the inspector, and explained the whole system in plain language. We finally have backup power we can actually use without extension cords everywhere.
Related Electrical Services
Electrical Panel Upgrades
Many Fall River generator hookups start with a panel that has no spare breaker spaces. We upgrade to a 200-amp panel with room for the transfer switch, which also clears the way for future circuits.
Electrical Panel UpgradesCircuit Breaker Replacement
A weak or tripping main breaker will not carry a generator feed reliably. We replace worn Square D, Eaton, or Siemens breakers before the hookup so the transfer switch has a solid source to work from.
Circuit Breaker ReplacementFuse Box Replacement
Older Fall River homes with 60-amp fuse boxes cannot accept a modern transfer switch. We replace the fuse box with a breaker panel first, then complete the portable generator hookup on the new service.
Fuse Box ReplacementElectrical Outlet Repair
Dead or loose outlets on your backed-up circuits defeat the purpose of a generator hookup. We repair them during the same visit so every circuit you plan to run on generator power actually works.
Electrical Outlet RepairGFCI Outlet Installation
Basements, garages, and kitchens near the generator inlet need GFCI protection under current code. We install them alongside the hookup so your storm-ready circuits meet Massachusetts requirements.
GFCI Outlet InstallationLight Switch Repair
A flickering or dead switch on a backed-up lighting circuit is worth fixing before an outage. We repair or replace switches while we are on site for the generator hookup.
Light Switch RepairElectrical Wiring Repairs
Rodent damage, deteriorated insulation, and loose splices all show up when we open walls for a generator feed. We repair the wiring so the new circuit runs on sound conductors, not compromised ones.
Electrical Wiring RepairsWhole-Home Rewiring
Homes with widespread wiring deterioration are poor candidates for a partial hookup. We rewire the house first, then install the transfer switch on a service we know is safe.
Whole-Home RewiringAluminum Wiring Repair
Aluminum branch wiring in 1960s and 1970s Fall River homes overheats at connections. We repair or pigtail those terminations before tying a generator feed into the same panel.
Aluminum Wiring RepairKnob and Tube Wiring Replacement
Knob and tube wiring has no equipment ground, which a generator hookup requires. We replace the affected runs so the transfer switch and inlet box can be properly grounded and bonded.
Knob and Tube Wiring ReplacementElectrical Code Corrections
Double-tapped breakers, missing cover plates, and ungrounded circuits fail inspection. We correct them as part of the hookup so the permit passes on the first visit.
Electrical Code CorrectionsSurge Protection Installation
Generator transfer switches can pass surges when utility power returns. We install panel-mounted surge protection to shield electronics on both generator and grid power.
Surge Protection InstallationWhole-House Surge Protectors
A whole-house surge protector at the panel pairs well with a generator hookup, protecting your furnace board, fridge, and router from the switchover spike when the grid comes back.
Whole-House Surge ProtectorsGenerator Installation
If you decide a portable unit is not enough, we install standby generators with automatic transfer switches. Many customers start with a portable hookup and upgrade later.
Generator InstallationStandby Generator Repair
Already have a standby unit that will not start? We diagnose and repair the transfer switch, battery, and control board so your backup power works when the storm hits.
Standby Generator RepairTransfer Switch Installation
The transfer switch is the heart of any generator hookup. We install manual and automatic switches sized to your panel and generator, with every lug torqued to manufacturer spec.
Transfer Switch InstallationCeiling Fan Installation
If a bedroom fan is on your backed-up circuit list, we can install or re-hang it during the same visit so the room stays comfortable during an outage.
Ceiling Fan InstallationCeiling Fan Repair
A fan that wobbles or hums on generator power usually has a loose connection or worn capacitor. We repair it while wiring the generator circuits.
Ceiling Fan RepairLight Fixture Installation
We install fixtures on the circuits you plan to back up, so your kitchen, stairwell, and hallway stay lit when the grid goes down.
Light Fixture InstallationRecessed Lighting Installation
Recessed lights draw little wattage, making them ideal generator-backed lighting. We install them on the transfer switch circuits to maximize your runtime.
Recessed Lighting InstallationOutdoor Lighting Installation
Security lights on a backed-up circuit keep your yard lit during an outage. We wire them to the transfer switch so they run on generator power.
Outdoor Lighting InstallationSecurity Lighting Installation
Motion and dusk-to-dawn security lights are a common add-on to generator hookups in Fall River, where outages often coincide with storm damage and downed lines.
Security Lighting InstallationLandscape Lighting Installation
Low-voltage landscape lighting can run on a backed-up circuit with the right transformer. We plan it into the hookup so your walkways stay visible.
Landscape Lighting InstallationMotion Sensor Light Installation
Motion sensors on generator-backed circuits deter theft during long outages. We install and aim them while completing the hookup.
Motion Sensor Light InstallationDimmer Switch Installation
Dimmers let you stretch generator wattage by lowering lighting load. We install them on backed-up circuits to extend runtime on a smaller portable unit.
Dimmer Switch InstallationSmart Home Electrical Installation
Smart switches and hubs need steady power to keep schedules and alerts running. We place them on backed-up circuits so your home stays connected during an outage.
Smart Home Electrical InstallationSmart Thermostat Installation
A smart thermostat on generator power keeps the furnace cycling and lets you monitor temperature remotely. We wire it into the backed-up circuit list.
Smart Thermostat InstallationEV Charger Electrical Repair
EV chargers draw too much for most portable generators, so we make sure the charger circuit stays off the transfer switch and repair any faults we find during the panel check.
EV Charger Electrical Repair200 Amp Electrical Panel Upgrade
A 200-amp upgrade gives you the breaker space and capacity a generator hookup needs. We handle both in one project, which is the most cost-effective path for older Fall River services.
200 Amp Electrical Panel UpgradeWhat Fall River Customers Say
Real experiences from customers who chose our Portable Generator Hookup services
"Our triple-decker had a 60-amp fuse box and I figured a generator hookup was impossible. The crew from Fall River RapidSpark replaced the panel and installed the inlet box and transfer switch in one day. When the October storm knocked out power for 14 hours, we ran the furnace and fridge without a single extension cord. Worth every dollar."
Maria S.
Homeowner, The Flint
"I bought a 7,500-watt generator and had no idea how to connect it safely. They mounted the inlet box on the side of the house, labeled six circuits, and walked me through the whole sequence. The inspector passed it on the first visit. I have used it three times since and it starts every time."
Dave L.
Homeowner, Highlands
"I manage two rentals and needed generator hookups on both. They quoted a fair price, pulled the permits, and finished both installs in two days. The tenants finally stopped calling me every time the power flickered. Clean work, and they cleaned up the basement when they were done."
Karen M.
Landlord, Corky Row
Get Your Portable Generator Hookup Fall River MA Scheduled
We are licensed, permitted, and ready before the next storm. Call (508) 446-9335 and we will quote your hookup over the phone, then get an electrician to your panel this week.