Generator Installation Fall River MA keeps your lights on
Standby power for homes and businesses across Bristol County
When the grid drops in Fall River, generator installation Fall River MA is what keeps your heat, fridge, and medical equipment running. We size, wire, and commission standby systems for homeowners in the Highlands, the Flint, and South End, plus small commercial buildings downtown. Whether you want a whole-house unit or a targeted backup circuit, our licensed electricians handle the transfer switch, the permit, and the final load test so the switchover is automatic the first time the power blinks.
What generator installation Fall River MA actually involves
Generator installation Fall River MA is the licensed electrical work of mounting a standby generator, wiring it to a transfer switch, and connecting it to your home's electrical panel so it starts automatically during an outage. We run the gas or propane feed coordination, pull the permit through the city, pour or anchor the pad, run conduit and THHN wire, install the automatic transfer switch, and commission the unit under load. A typical whole-house job takes one to two days on site, plus inspection scheduling.
Fall River's housing stock makes this trickier than a new-build subdivision. Plenty of homes in Corky Row and Globe Village still have 100-amp panels, knob and tube remnants, or aluminum branch wiring that has to be corrected before a generator can legally carry the load. Winter nor'easters and summer storm cells knock out power here often enough that a standby generator installation Fall River is less a luxury and more a resilience upgrade. If you have a sump pump, a medical device, or a home office, the math changes fast.
Why Fall River homeowners add standby power
A generator is only as good as the wiring behind it. Here is what a properly installed system actually delivers when the utility feed goes down.
Automatic switchover in seconds
The transfer switch senses the outage and starts the generator within 10 to 30 seconds, no manual cord pulling. Your furnace, well pump, refrigerator, and internet stay live. We test the sequence under real load before we leave, so you know the exact behavior when the grid drops at 2 a.m.
Protection for sump pumps
Fall River basements flood fast when a storm knocks out power and the sump pump dies. A backup generator installation near me Fall River keeps that pump running through the worst of it. We put the pump on a dedicated circuit so it never competes with the dryer or oven for generator capacity.
Code-compliant transfer switching
Backfeeding a panel through a dryer outlet is illegal and deadly to linemen. We install listed automatic transfer switches from Square D, Eaton, or Siemens that mechanically break the utility feed before the generator energizes. That is what makes the system pass inspection and keeps your insurance valid.
One panel, one clear load map
We label every backed-up circuit in the panel and give you a load sheet showing what runs on generator power. If you later add central air or an EV charger, you know exactly how much headroom is left. Most 22 kW air-cooled units carry a 200-amp home comfortably.
How our generator installation process runs
From the first call to the final load test, here is the sequence you will experience. Most residential jobs wrap in one to two days of on-site work.
Load assessment
We walk your panel, list every major appliance, and calculate running and starting watts. A 4-ton AC unit can pull 60 amps on startup, which changes the generator size. You get a written load calculation and a clear recommendation, usually within the same visit.
Sizing and placement
We pick the generator size and the pad location, keeping exhaust at least 5 feet from windows, doors, and fresh-air intakes per NFPA 37. We check gas meter capacity and confirm the propane or natural gas feed can carry the unit under full load.
Permits and inspection
We pull the electrical permit with the city and coordinate the gas permit if needed. Massachusetts requires inspection before the generator is energized, so we schedule that early. You do not chase paperwork; we handle the sequence and tell you what to expect.
Install and wiring
The crew sets the pad, mounts the generator, runs conduit and conductors, installs the automatic transfer switch, and lands the circuits. We torque every lug to spec with a calibrated wrench and label the panel. Most homes take one full day for this stage.
Commissioning and test
We start the unit, simulate an outage, and watch the transfer under real load. Voltage and frequency get checked with a Fluke meter, and we confirm the generator carries the HVAC, well pump, and fridge at the same time. You get a walkthrough and a maintenance schedule before we pack up.
Local experience you can verify on site
Our electricians hold Massachusetts Electrical License credentials and work to NEC and NFPA 70E standards on every job. We have installed and serviced standby systems across Bristol County, from 100-amp cottages in the South End to 400-amp commercial services downtown. We know which Fall River panels accept a generator interlock kit and which ones need a full upgrade first. That local pattern recognition saves you money and inspection headaches.
- Massachusetts Electrical License holders who pull permits and pass city inspection
- NFPA 70E and OSHA safety certification on every crew member
- Experienced with Square D, Eaton, Siemens, and Generac transfer equipment
- Load calculations done with Fluke meters and manufacturer sizing software
- Familiar with Fall River's older 100-amp panels and aluminum branch wiring
Why our generator installation Fall River MA work holds up
We are electricians first, generator installers second. That order matters when your panel is old, your grounding is questionable, or your service entrance needs work before a generator can be added.
Licensed and permitted
Every job is pulled under a Massachusetts Electrical License and inspected by the city. We do not cut corners on transfer switch listing or grounding electrode conductor sizing. If an inspector flags something, we fix it, not you.
Real load testing
We simulate an outage and run the house on generator power before we call the job done. You see the transfer happen. If the AC compressor stalls the unit, we catch it then, not during a February storm when you need heat.
Panel work included when needed
Many Fall River homes need a 200 amp electrical panel upgrade before a whole-house generator makes sense. We quote that as part of the same project, so you are not coordinating two contractors. One permit, one inspection, one clean install.
Service after the sale
We handle standby generator repair, annual maintenance, and battery replacement for the units we install. A generator that sits unused for 11 months needs a real exercise cycle and an oil check. We keep it ready so it starts when it matters.
What our generator installation includes
Every standby project we quote covers the electrical scope end to end. We handle the permit, the transfer switch, the wiring, and the commissioning test. Gas piping and the generator unit itself are quoted separately because they vary by fuel type and size.
What's Included
Load calculation and sizing
We list every appliance, measure running and starting watts, and size the generator to your actual house. That prevents the two most common mistakes: an undersized unit that stalls on AC startup and an oversized unit you paid too much for.
Automatic transfer switch
A listed Square D, Eaton, or Siemens transfer switch sized to your service, mounted and wired to break the utility feed before the generator energizes. This is the component that makes the system legal, safe, and automatic.
Permit and inspection
We pull the electrical permit with the city, coordinate the gas permit when required, and meet the inspector on site. You get the signed-off sticker and the paperwork for your records without making a single phone call.
Conduit, wiring, and terminations
Conduit runs, THHN conductors, junction boxes, and torqued lugs to manufacturer spec. We use Klein Tools and Milwaukee equipment and label every circuit in the panel so future service is straightforward.
Commissioning and load test
We start the unit, simulate an outage, and verify voltage and frequency under real load with a Fluke meter. You watch the transfer happen. If anything is off, we adjust it before we leave the property.
Problems a standby generator solves in Fall River
Most of our generator calls start with a specific failure the homeowner never wants to repeat. Here are the ones we hear most often, and how a properly installed system handles them.
Sump pump dies during a storm outage
A finished basement can take on inches of water in under an hour, ruining drywall, flooring, and stored belongings. Insurance may cover it, but the disruption lasts months.
We put the sump pump on a dedicated backed-up circuit and size the generator to carry it alongside the furnace and fridge. During the transfer test we confirm the pump runs on generator power before we call the job complete.
Medical equipment loses power overnight
CPAP machines, oxygen concentrators, and refrigerated medication all depend on continuous power. A multi-hour outage becomes a health risk, not an inconvenience.
We identify the medical circuits, put them on the backed-up panel, and add a small UPS at the device for the 10 to 30 second transfer window. You get a labeled panel showing exactly which outlets stay live.
Repeated outages from aging utility infrastructure
Fall River's older neighborhoods see more frequent and longer outages after nor'easters and summer storms. Each one costs spoiled food, hotel nights, and lost work time.
An automatic standby generator installation Fall River removes the outage from your life. The unit exercises weekly, starts on its own, and runs until utility power returns. No extension cords, no manual start, no guesswork.
Illegal backfeeding through a dryer outlet
Backfeeding a panel without a transfer switch sends voltage onto the utility lines and can electrocute a lineman. It also voids homeowner insurance if a fire traces back to the setup.
We remove the suicide cord approach entirely. A listed transfer switch or an outdoor inlet box with an interlock kit makes portable and standby generator hookups code-compliant and safe for everyone on the block.
When Fall River properties need backup power
A Highlands homeowner with a finished basement and a sump pump that runs every storm.
We size a 22 kW air-cooled unit, put the sump pump, furnace, fridge, and a lighting circuit on the backed-up panel, and install an automatic transfer switch. The generator exercises weekly and starts on its own when the utility drops.
The basement stays dry through multi-day outages, and the family never has to bail water by flashlight again.
A South End two-family with a 100-amp panel and aluminum branch wiring.
We upgrade the service to 200 amps, repair the aluminum connections with listed connectors, and install the transfer switch and generator in one permitted project. The inspector signs off on the whole scope in a single visit.
Both units have backed-up heat and refrigeration, and the building's wiring is now insurable and code-compliant.
A downtown commercial building that needs egress lighting and a server room to stay live.
We run a load calculation on the critical circuits, install a 30 kW unit with an automatic transfer switch, and separate the backed-up panel from the general load. Staff get a walkthrough of the transfer sequence.
The building stays open during outages, the server room never reboots unexpectedly, and egress lighting meets code.
A homeowner on the Tiverton Line who wants backup but is not ready for a permanent unit.
We install a manual transfer switch and an outdoor inlet box rated for a portable generator. The setup is code-compliant, and the door is open to a standby unit later without rewiring the panel.
They can run the furnace and fridge from a portable generator during storms, with no backfeeding risk and no permit problems.
Tools and methods we use on generator jobs
Tools & Equipment
Fluke multimeter and voltage tester
Verifies voltage, frequency, and phase rotation at the generator terminals and the transfer switch before and after commissioning. A generator running at the wrong frequency can damage HVAC control boards.
Klein Tools and Milwaukee hand tools
Lineman's pliers, wire strippers, insulated screwdrivers, and cable rippers for clean terminations. Insulated handles matter when working near an energized utility feed during transfer switch wiring.
Torque wrench
Lug torque on generator terminals, transfer switch lugs, and panel main connections is specified by the manufacturer. Under-torqued lugs arc and overheat; over-torqued lugs strip. We follow the spec sheet.
Conduit bender and fish tape
Bends and routes conduit from the generator pad to the transfer switch and panel. Clean conduit work protects THHN conductors from weather and physical damage and passes inspection without rework.
Circuit breaker finder and GFCI tester
Maps which breaker feeds each outlet before we move circuits to the backed-up panel. Also confirms GFCI protection on kitchen, bath, and garage circuits that end up on generator power.
Non-contact voltage pen
Quick safety check before opening any panel or transfer switch enclosure. Confirms the utility feed is actually dead before we land conductors, which is the first rule on every job.
Methods
NEC load calculation
We calculate running and starting watts for every appliance on the backed-up panel using NEC Article 220 methods. Starting watts on motors and compressors drive the generator size more than running watts, which is why a 4-ton AC unit can push a home from 14 kW to 22 kW.
NFPA 37 clearance and placement
Standby generators need specific clearances from windows, doors, fresh-air intakes, and combustible surfaces. We site the pad to meet NFPA 37 so exhaust does not enter the home and the installation passes inspection on the first visit.
NFPA 70E safe work practices
Arc-flash boundaries, PPE, and lockout procedures apply to generator commissioning just like any energized panel work. Our crew follows NFPA 70E on every job, which is also an OSHA requirement for electrical work.
Break-before-make transfer testing
We verify the transfer switch mechanically breaks the utility feed before the generator contacts close. That sequence protects linemen and prevents the generator from fighting the grid. We test it under real load, not just on a meter.
How generator installation runs in Fall River
Fall River sits on the south coast, which means nor'easters, tropical remnants, and ice storms all hit the same grid. Outages here tend to be longer than inland because of the overhead distribution and the age of some feeders. The housing stock adds another layer: homes in Corky Row, Globe Village, and parts of the Flint often have 100-amp services, aluminum branch wiring, or knob and tube that has to be corrected before a generator can legally carry the load. We handle those corrections under the same permit. Winter is the busy season for standby generator installation Fall River, so we schedule load assessments early in the fall. Summer storm work fills in behind it. If you want emergency generator installation in Fall River Massachusetts after a storm has already knocked you out, call us and we will tell you honestly what can be scheduled and what has to wait for a permit.
Service Areas
Larger lots and detached garages make pad placement straightforward. Many homes here already have 200-amp service, which shortens the install timeline.
Dense older housing with a mix of 100-amp panels and updated services. We often combine a panel upgrade with the generator install to avoid a second permit.
Historic homes with knob and tube remnants and tight side yards. Generator placement needs careful clearance planning for exhaust and service access.
Many two- and three-family buildings where a single standby unit can back up critical circuits for multiple units if the service is configured correctly.
Larger properties and rural edges where portable generator hookups with an outdoor inlet box are a common first step before a permanent standby unit.
Local Considerations
Coastal nor'easters and ice storms
These are the events that cause multi-day outages. A standby generator sized for winter heating loads keeps the furnace, fridge, and sump pump running when the grid is down for 48 hours or more.
Aging 100-amp service entrances
Many Fall River homes cannot support a whole-house generator without a service upgrade. We quote the 200-amp panel upgrade as part of the same project so there is one permit and one inspection.
Aluminum branch wiring in mid-century homes
Aluminum connections loosen and overheat under load. We repair them with listed connectors before adding generator-backed circuits, which keeps the installation insurable and code-compliant.
Natural gas meter capacity limits
A whole-house generator pulls significant gas volume. We verify meter capacity with the utility before sizing the unit, so the generator does not starve the furnace or water heater during an outage.
Highlands home, storm-ready in two days
A 2,200 square foot home with a 100-amp panel, a finished basement, and a sump pump that flooded twice in three years. The family ran extension cords to a portable generator during outages and still lost the basement once.
We upgraded the service to 200 amps, installed a 22 kW air-cooled standby unit with an automatic transfer switch, and put the sump pump, furnace, fridge, and lighting on the backed-up panel. The next outage transferred in 14 seconds with no water in the basement.
Maintenance & Follow-up
Annual oil and filter change, battery check, and a load test each fall before storm season. The unit exercises weekly on its own schedule, which keeps the battery charged and the seals lubricated.
A two-family with a 60-amp fuse box, aluminum branch wiring in the kitchen, and no path to a legal generator install. The owner had been quoted two separate projects by other contractors and did not want two inspections.
We replaced the fuse box with a 200-amp panel, repaired the aluminum connections with listed connectors, and installed a 26 kW unit serving both units' critical circuits. One permit, one inspection, signed off on the first visit.
Maintenance & Follow-up
We check the aluminum connectors and torque the panel lugs at the annual service, along with the generator oil change and transfer test. The owner gets a written report each year.
A small commercial building with a server room, egress lighting, and a POS system that dropped every time the utility blinked. The owner was losing transactions and rebooting servers several times a year.
We installed a 30 kW unit with an automatic transfer switch and separated the critical panel from the general load. The server room now rides through outages without a reboot, and egress lighting stays lit for the full duration.
Maintenance & Follow-up
Quarterly exercise checks and an annual load bank test keep the unit ready. We also verify the UPS batteries in the server room at each visit, since they cover the 10 to 30 second transfer window.
What generator installation costs in Fall River
Typical 2026 pricing for a residential standby generator installation in Fall River runs $4,500 to $9,500 for the electrical scope, plus the generator unit itself at $2,800 to $6,500 depending on size and fuel type. A 200-amp panel upgrade, if needed, adds $1,800 to $3,200. We give you a written number after the load assessment. Affordable standby generator installation Fall River is about right-sizing the unit, not buying the cheapest one on the shelf.
Pricing Factors
Generator size and fuel
A 14 kW air-cooled propane unit costs less than a 26 kW liquid-cooled natural gas unit. Fuel type also affects the install because propane requires a tank and regulator, while natural gas needs meter capacity verification.
Transfer switch type
A 200-amp service-rated automatic transfer switch costs more than a 100-amp model. Whole-house switches with load management modules add cost but let a smaller generator carry a larger house.
Panel condition and age
A modern 200-amp panel with open spaces is quick to tie into. A 100-amp panel, a fuse box, or a panel with double-tapped breakers adds labor and may require a full upgrade before the generator can be installed.
Wiring and conduit distance
The farther the generator pad sits from the panel, the more conduit, THHN wire, and labor the job takes. A 15-foot run is straightforward; a 60-foot run through a finished basement adds cost.
Permits and inspection
Electrical and gas permits are required and vary by scope. We include permit costs in the quote so there is no surprise line item after the work is done.
Existing code violations
Missing grounds, aluminum wiring, or knob and tube must be corrected before a generator can legally carry the load. We identify these during the assessment and quote the correction in the same project.
Investment Range
$4,500 - $9,500 for the electrical scope, plus $2,800 - $6,500 for the generator unit
Based on project scope
Value You Get
A standby generator protects your basement, your food, your medical equipment, and your ability to stay in the house during a multi-day outage. Spread over the 15 to 20 year life of the unit, the cost per storm season is modest compared to a hotel stay and a flooded basement.
How much does generator installation cost in Fall River?
Most residential standby generator installations in Fall River run $4,500 to $9,500 in 2026, including the transfer switch, permit, and labor. The generator itself is usually $2,800 to $6,500 depending on size. If your panel needs a 200-amp upgrade first, add $1,800 to $3,200. We give you a written number after the load assessment, not a phone guess.
What size generator do I need for my Fall River home?
A typical 1,800 to 2,400 square foot Fall River home with natural gas heat needs a 14 kW to 22 kW air-cooled standby unit. If you have central air, a well pump, and an electric range, you are at the top of that range. We do a running-watt and starting-watt calculation on your actual appliances before recommending a size.
How long does standby generator installation take in Fall River Massachusetts?
On-site work is usually one to two days. The full timeline from signed quote to running system is typically two to four weeks because of permit review, gas meter coordination, and inspection scheduling. We handle all of that sequencing. You are only involved for the initial assessment and the final walkthrough.
Do I need a permit for generator installation in Fall River MA?
Yes. Massachusetts requires an electrical permit and inspection for any standby generator installation, and most installations also need a gas permit. We pull both. The inspection confirms your transfer switch is listed, your grounding is correct, and your generator clearances meet NFPA 37. Skipping the permit can void insurance coverage after a fire.
Licensed, permitted, and inspected
Certifications
Reviews
They handled the permit, the panel upgrade, and the generator install in one project. The transfer test was thorough and they labeled every circuit. First inspection passed. I would use them again for anything electrical.
Our sump pump used to flood the basement every big storm. After the standby install, we rode out a 36-hour outage with dry floors and a warm house. The crew was clean and explained the maintenance schedule clearly.
Called about a generator that would not transfer. They diagnosed a failed transfer switch, replaced it, and tested the whole system the same visit. Fair price and no upsell on a new generator when the old one was fine.
Professional from the first call. Load calculation was detailed, the quote was itemized, and the install matched the quote. They coordinated the gas permit and the inspection so we did not have to chase anything.
Related Services
Electrical Panel Upgrades
Most standby generators need a panel with enough spaces and a clean main breaker. We upgrade 100-amp services to 200 amps as part of the generator project so the transfer switch has a proper home and your backed-up circuits are clearly labeled.
Electrical Panel UpgradesCircuit Breaker Replacement
A weak main breaker or a failing 30-amp dryer breaker can cause nuisance trips once a generator is carrying the house. We replace worn breakers with Square D or Eaton units rated for the load before commissioning your standby system.
Circuit Breaker ReplacementFuse Box Replacement
You cannot legally tie a modern automatic transfer switch into a 60-amp fuse box. If your Fall River home still runs on fuses, we replace the box with a breaker panel first, then install the generator. One permit covers both scopes.
Fuse Box ReplacementElectrical Outlet Repair
Dead outlets and loose receptacles are a sign of backstabbed wiring or a failing circuit. We fix those before generator installation so the backed-up circuits actually work when the utility drops and the transfer switch engages.
Electrical Outlet RepairGFCI Outlet Installation
Generator-backed circuits in kitchens, baths, and garages still need GFCI protection. We install Leviton and Hubbell GFCI receptacles on the backed-up circuits so your generator power meets code in wet locations.
GFCI Outlet InstallationLight Switch Repair
Flickering lights on a generator circuit often trace back to a worn switch or a loose splice. We repair or replace switches during the install so every backed-up lighting circuit behaves the same on generator power as it does on utility power.
Light Switch RepairElectrical Wiring Repairs
Rodent damage, deteriorated insulation, and loose junctions all show up when we open walls for generator wiring. We repair those runs while the walls are accessible, saving you a second service call later.
Electrical Wiring RepairsWhole-Home Rewiring
Homes with knob and tube or degraded cloth wiring cannot safely carry generator power. We rewire those circuits with Romex cable and modern junction boxes before the transfer switch goes in, so the whole system is code-compliant.
Whole-Home RewiringAluminum Wiring Repair
Aluminum branch wiring is a fire hazard and a code problem on any generator-backed circuit. We repair it with listed AlumiConn connectors or copper pigtails before commissioning your standby system, which keeps the installation insurable.
Aluminum Wiring RepairKnob and Tube Wiring Replacement
Knob and tube has no equipment ground, which fails generator inspection. We replace those runs with grounded Romex so your transfer switch, panel, and backed-up circuits all meet current NEC requirements.
Knob and Tube Wiring ReplacementElectrical Code Corrections
Double-tapped breakers, missing grounds, and undersized service conductors all surface during a generator inspection. We correct those violations as part of the project so the city signs off on the first visit.
Electrical Code CorrectionsSurge Protection Installation
A generator transfer creates its own surge event. We install whole-house surge protection at the panel to protect electronics during both utility switching and generator startup, extending the life of your HVAC control boards.
Surge Protection InstallationWhole-House Surge Protectors
Type 2 surge protective devices from Square D or Eaton mount at the panel and divert transient voltage before it reaches your appliances. Pairing one with a standby generator protects the equipment the generator is meant to keep running.
Whole-House Surge ProtectorsStandby Generator Repair
If your existing unit will not crank, runs rough, or fails to transfer, we diagnose the battery, controller, and transfer switch. We repair Generac, Kohler, and Briggs & Stratton units across Fall River and Bristol County.
Standby Generator RepairPortable Generator Hookup
Not ready for a standby unit? We install a manual transfer switch or an outdoor inlet box so you can run a portable generator safely without backfeeding a dryer outlet. It is a code-compliant middle step.
Portable Generator HookupTransfer Switch Installation
The transfer switch is the heart of any generator system. We install automatic and manual switches rated for your service size, wire them to the panel, and test the break-before-make sequence under load.
Transfer Switch InstallationCeiling Fan Installation
Ceiling fans pull small but steady wattage. We install and balance them on backed-up circuits so air movement continues during a summer outage, which matters in second-floor bedrooms.
Ceiling Fan InstallationCeiling Fan Repair
A fan that hums or wobbles on utility power will do the same on generator power. We repair bearings, capacitors, and pull-chain switches so your backed-up circuits are not carrying a failing motor.
Ceiling Fan RepairLight Fixture Installation
We install LED fixtures on generator-backed lighting circuits so your outage load stays low. LED draws a fraction of what incandescent does, which lets a smaller generator carry more of the house.
Light Fixture InstallationRecessed Lighting Installation
Recessed LED cans distribute light evenly and draw very little wattage. We wire them on backed-up circuits so hallways, stairwells, and kitchens stay lit during a transfer event.
Recessed Lighting InstallationOutdoor Lighting Installation
Security and pathway lighting on a generator circuit keeps your exterior visible during an outage. We install fixtures rated for wet locations and wire them to a backed-up circuit in the panel.
Outdoor Lighting InstallationSecurity Lighting Installation
Motion-activated security lights on generator power deter opportunistic activity during neighborhood outages. We install and aim them so driveways and side entries stay covered when the street goes dark.
Security Lighting InstallationLandscape Lighting Installation
Low-voltage landscape lighting runs through a transformer that needs a live circuit. We put that transformer on a generator-backed circuit so your yard lighting survives an extended outage.
Landscape Lighting InstallationMotion Sensor Light Installation
Motion sensors draw a small standby load and switch on instantly. We install them on backed-up circuits at garages, side doors, and basements so you are not fumbling for a flashlight during a transfer.
Motion Sensor Light InstallationDimmer Switch Installation
Modern LED-compatible dimmers prevent flicker on generator power, which is common with older rheostats. We install Lutron and Leviton dimmers rated for the LED loads on your backed-up lighting circuits.
Dimmer Switch InstallationSmart Home Electrical Installation
Smart hubs, routers, and cameras need continuous power to stay online. We put those circuits on the generator and install a small UPS at the hub so your home network survives the 10 to 30 second transfer window.
Smart Home Electrical InstallationSmart Thermostat Installation
A smart thermostat keeps your heating schedule intact during an outage, but only if its transformer circuit is backed up. We wire the HVAC control circuit to the generator so the thermostat and furnace both stay live.
Smart Thermostat InstallationEV Charger Electrical Repair
EV chargers pull 32 to 48 amps continuously, which can exceed generator capacity. We assess whether your charger should be on the backed-up panel or left on utility-only, and repair faulty chargers while we are on site.
EV Charger Electrical Repair200 Amp Electrical Panel Upgrade
A 200-amp panel is the practical baseline for whole-house standby power. We upgrade your service, install the new panel and main breaker, and land the transfer switch in the same visit so the generator has a proper foundation.
200 Amp Electrical Panel UpgradeWhat Fall River customers say
Real experiences from customers who chose our Generator Installation services
"We lost power for three days in a February storm two years ago and swore we would never do that again. The crew sized a 22 kW unit for our house, upgraded the panel to 200 amps, and tested it with the heat and fridge running. It transferred in about 15 seconds during the next outage. Worth every penny."
Maria S.
Homeowner, Highlands
"My old fuse box was never going to pass inspection with a generator tied in. They replaced the box, ran new circuits, and installed the transfer switch in one project. The inspector signed off first visit. They also labeled every backed-up circuit so I know what runs on generator power."
Dave R.
Homeowner, South End
"We manage a small commercial building and needed backup for the server room and egress lighting. They did the load calculation, installed a 30 kW unit, and walked our staff through the transfer sequence. Clean conduit work, permits pulled, and no surprises on the invoice."
Jen M.
Property Manager, Downtown Fall River
Get your generator installation Fall River MA quote
We assess your panel, size the generator, and give you a written number before any work starts. Licensed Massachusetts electricians, permits handled, live transfer test included. Call (508) 446-9335 or request a visit online and we will schedule your load assessment this week.